# "DIY" dedicated line

**URL:** <https://forum.psaudio.com/t/diy-dedicated-line/28785>\
**Category:** Power Components\
**Created:** [April 27, 2022, 12:38am UTC](https://forum.psaudio.com/t/diy-dedicated-line/28785 "2022-04-27T00:38:09Z")\
**Posts on this page:** 6\
**Page:** 2

<div class="post-metadata">

**Author:** ![Baldy](https://sea1.discourse-cdn.com/flex015/user_avatar/forum.psaudio.com/baldy/32/223847_2.png) [@Baldy](https://forum.psaudio.com/u/Baldy)\
**Post date:** [April 29, 2022, 5:54pm UTC](https://forum.psaudio.com/t/diy-dedicated-line/28785/21 "2022-04-29T17:54:42Z")

</div>

Same here in SW Michigan. I believe it comes off the spool twisted like that probably so it stays together in the free air spans.

---

<div class="post-metadata">

**Author:** ![brian.fitterman](https://avatars.discourse-cdn.com/v4/letter/b/bbce88/32.png) [@brian.fitterman](https://forum.psaudio.com/u/brian.fitterman)\
**Post date:** [April 29, 2022, 6:03pm UTC](https://forum.psaudio.com/t/diy-dedicated-line/28785/22 "2022-04-29T18:03:23Z")

</div>

Yeah I think that is pretty standard for triplex wiring.

---

<div class="post-metadata">

**Author:** ![Arenith](https://sea1.discourse-cdn.com/flex015/user_avatar/forum.psaudio.com/arenith/32/62875_2.png) [@Arenith](https://forum.psaudio.com/u/Arenith)\
**Post date:** [April 29, 2022, 9:50pm UTC](https://forum.psaudio.com/t/diy-dedicated-line/28785/23 "2022-04-29T21:50:30Z")

</div>

That’s the point really. Having the line&neutral twisted also for the internal dedicated line in the room is what I want too. Least interference and least radiation too, and least common mode too with running a parallel ground.  
(It would run fairly close to other lines so I really want the electromagnetic benefit described)

For the _feed_ from meter to house, it would be what’s available for 25sqmm aluminium, not customizable really.

---

<div class="post-metadata">

**Author:** ![Baldy](https://sea1.discourse-cdn.com/flex015/user_avatar/forum.psaudio.com/baldy/32/223847_2.png) [@Baldy](https://forum.psaudio.com/u/Baldy)\
**Post date:** [April 29, 2022, 10:25pm UTC](https://forum.psaudio.com/t/diy-dedicated-line/28785/24 "2022-04-29T22:25:21Z")

</div>

Depending on local codes you could always buy individual wires and twist the wires however you wanted and then pull them thru conduit.

---

<div class="post-metadata">

**Author:** ![Vmax](https://sea1.discourse-cdn.com/flex015/user_avatar/forum.psaudio.com/vmax/32/19896_2.png) [@Vmax](https://forum.psaudio.com/u/Vmax)\
**Post date:** [April 30, 2022, 1:04am UTC](https://forum.psaudio.com/t/diy-dedicated-line/28785/25 "2022-04-30T01:04:58Z")

</div>

Twisting solid 9 gauge conductors by hand and then having to route them without the orange slippery outer sleeve through walls and wall headers could be a challenge. I had tough enough time with 10 gauge Romex times four as a DIY.

---

<div class="post-metadata">

**Author:** ![Arenith](https://sea1.discourse-cdn.com/flex015/user_avatar/forum.psaudio.com/arenith/32/62875_2.png) [@Arenith](https://forum.psaudio.com/u/Arenith)\
**Post date:** [April 30, 2022, 9:59am UTC](https://forum.psaudio.com/t/diy-dedicated-line/28785/26 "2022-04-30T09:59:48Z")

</div>

> [@vkennedy61](#):
>
> What I don’t know, and mind you I only briefly poked at this, is what constitutes “high end breaker”?

> **[GigaWatt G-16A 1P](https://www.technologyfactory.eu/en/gigawatt/power-outlets-fuses/gigawatt-g-c16a/a-15281-10001182)**
>
> 1-POLE Circuit Breaker

This is apparently an example of a legitimately high-end breaker.

[Previous page](https://forum.psaudio.com/t/diy-dedicated-line/28785.md?page=1)