Modding the DirectStream DAC

You should think about returning the DSD to the tech that did the mod to get a “professional” opinion.

2 Likes

After a few hours of testing going back to the Sophia mono’s and even putting a pre-amp in I will be going back to the tech who installed the Edcor’s for professional troubleshooting. Thanks all

2 Likes

Smart move

1 Like

Did you get this sorted out?

1 Like

Yes, thanks for the reminder @jkrichards. There was no issue found with the Directstream, the Edcor’s, or the installation. We actually determined that the right ribbon tweeter on my Scansonic MB-5B was starting to fail and that was the cause of the problem. The MB-5B is under warranty so dealing with that now.

I have a backup pair of Scansonic MB-5’s that I moved into the main system and the Directstream is functioning perfectly. Crisis averted. Thanks everyone who chimed in.

6 Likes

My Edcor 4400 transformers arrived and will be installed by a local technician. Is it easy to remove the analog board so I don’t have to transport the entire DAC?

1 Like

It’s pretty simple. The smaller digital board is on top of the analog board. Several screws on the outputs and inputs on the outside and there are two plugs to disconnect on the board. It will save you money.

Four screws on the bottom. I use a suction cup that I have to remove glass off an IMac to remove DSD l over. This Video helps. I use the suction device instead of the all thread method in this video. Good luck and you will love the Edcor upgrade!

Thanks! Looking forward to it.

1 Like

Oops I almost forgot a very important step! Don’t forget to wear a anti-static strap when working on the dac during the removal and reinstall process!

1 Like

Hey! Is there any member here I can pay to make me an internal power cable so I can run an external power supply?

1 Like

There is some good info in this thread regarding a “star quad 14 awg” power cable…think Mr. Smith said it caught his eye as a very good fit. It’s what I used, and several others. A year later, it’s still kicking butt.

I have some extra connectors and sockets. I can mail to you if you pay postage. You can source DC cables with other connectors right length then take off the end you don’t need and crimp and solder the board connector on. I am not a cable maker but did a semi DYI.

I used Ghent Gotham cable I bought and did just that.

These are the best sounding and most shielded ones ones but there are cheaper ones too on his site. The express shipping from china is fast.

https://www.ghentaudio.com/part/dc-gac4.html

If you can wait a bit, we are designing a plug and play solution that will allow you to use the internal PS or the external one. If no external PS is hooked up the unit will use the internal PS. If the external PS is hooked up then the External PS will be used. It will be automatic and also will pass the power to the analog board at the correct time during power up. This will be a card that slides in the Bridge port with the external power supply connector and LED indicator. All one needs to do is move the analog PS plug to the new board and connect the supplied cable to the analog board. Kit will include the cable with the 2 pin connectors for the external power supply and the DSD.
We make the cables out of 14AWG 2.4mm OD Silver Plated FEP Wire High Purity OFC Copper Cable.

5 Likes

Hi - please forgive me if this is widely known, but who is “we”?

Thanks!

My E.E. Son and myself.

Ahhh, Fantastic!

I’m looking forward to seeing your board. It’s a very clever idea. I imagine there will be several questions about shielding… (hint) :wink:

Shielding will be no issue as this board, which has the complete bottom shielded sits on top of the power supply board which has the whole top shielded.

1 Like

Any idea on price?

Less then $200

4 Likes